Material · Operation	Gweike Cloud	Full Spectrum Laser Muse Core
3mm Baltic Birch Plywoodcut	18 mm/s · 90% · air assist	20 mm/s · 65% · air assist
3mm Basswood Plywoodcut	25 mm/s · 35% · air assist	20 mm/s · 40% · air assist
3mm Clear Acryliccut	15 mm/s · 50% · air assist	15 mm/s · 55% · air assist
3mm MDFcut	30 mm/s · 65–75% · air assist	15 mm/s · 48% · air assist
3mm Walnut Plywoodcut	-	20 mm/s · 68%
6mm Baltic Birch Plywoodcut	10 mm/s · 90% · air assist	15 mm/s · 80%
6mm MDFcut	-	15 mm/s · 85%
Bamboo 3mmcut	-	25 mm/s · 78%
Bamboo Cutting Boardcut	-	15 mm/s · 80–85% · air assist
Bamboocut	-	300 mm/min · 80–85% · 2× passes · air assist
Basswoodcut	-	20 mm/s · 60% · air assist
Cardboardcut	-	35 mm/s · 45%
Cardstockcut	-	45 mm/s · 25%
Chipboard 2mmcut	-	30 mm/s · 50%
Cork 3mmcut	-	35 mm/s · 38%
Corkcut	-	25 mm/s · 55%
Cotton Fabriccut	-	50 mm/s · 32%
Denim Fabriccut	-	40 mm/s · 40%
Faux Leathercut	-	35 mm/s · 45%
Genuine Leather (Veg-Tan, ~3mm)cut	-	30 mm/s · 45–55% · air assist
Genuine Leathercut	15 mm/s · 60–65% · air assist	10 mm/s · 70–75% · air assist
Kraft Papercut	-	125 mm/s · 8%
Leathercut	-	10 mm/s · 55% · air assist
Maplecut	-	15 mm/s · 65–75%
Plywoodcut	-	20 mm/s · 65% · air assist
Rubber Stamp Materialcut	-	10 mm/s · 80–85% · air assist
Walnutcut	-	15 mm/s · 65–75%
3mm Baltic Birch Plywoodengrave	-	315 mm/s · 15–20%
3mm Basswood Plywoodengrave	335 mm/s · 28%	315 mm/s · 30%
3mm Clear Acrylicengrave	240 mm/s · 10–15%	210 mm/s · 15–20%
3mm MDFengrave	435 mm/s · 20–28%	260 mm/s · 10–15%
3mm Walnut Plywoodengrave	-	400 mm/s · 18%
Anodized Aluminumengrave	-	210 mm/s · 20% · air assist
Bamboo 3mmengrave	-	400 mm/s · 22%
Bamboo Cutting Boardengrave	-	260 mm/s · 35%
Bambooengrave	-	300 mm/min · 55%
Basswoodengrave	-	315 mm/s · 15–20%
Cardboardengrave	-	525 mm/s · 10–15%
Cardstockengrave	-	525 mm/s · 5–10%
Ceramic Tileengrave	-	260 mm/s · 55%
Chipboard 2mmengrave	-	420 mm/s · 18%
Coated Stainless Steel Tumblerengrave	-	300 mm/min · 50%
Corkengrave	-	420 mm/s · 15–20%
Cotton Fabricengrave	-	525 mm/s · 9%
Denim Fabricengrave	-	440 mm/s · 12%
Faux Leatherengrave	-	525 mm/s · 12%
Genuine Leather (Veg-Tan, ~3mm)engrave	-	315 mm/s · 14–20% · air assist
Genuine Leatherengrave	240 mm/s · 22%	210 mm/s · 25%
Glassengrave	-	365 mm/s · 10–14%
Kraft Paperengrave	-	525 mm/s · 8%
Leatherengrave	-	155 mm/s · 15–20%
Mapleengrave	-	260 mm/s · 20–25%
Marble Tileengrave	-	80 mm/s · 50%
Plywoodengrave	-	315 mm/s · 15–20%
Rubber Stamp Materialengrave	-	155 mm/s · 50%
Slate (coaster)engrave	-	365 mm/s · 15–22%
Slateengrave	290 mm/s · 60%	260 mm/s · 65%
Stainless Steelengrave	-	230 mm/s · 58%
Walnutengrave	-	260 mm/s · 20–25%

All Gweike Cloud settings →All Full Spectrum Laser Muse Core settings →

Shopping for a Gweike Cloud? Check the current price.

See price on Amazon →

Shopping for a Full Spectrum Laser Muse Core? Check the current price.

See price on Amazon →

Frequently Asked Questions

Which is better, the Gweike Cloud or Full Spectrum Laser Muse Core?

It depends on your use case. Gweike Cloud is 50W co2. Full Spectrum Laser Muse Core is 45W co2. See the decision guide and side-by-side specs above.

What materials can both the Gweike Cloud and Full Spectrum Laser Muse Core cut or engrave?

Both machines have community-tested settings for 7 shared materials. The settings table above lists every material with side-by-side speed, power, passes, and air assist values for direct comparison.

Is the Gweike Cloud (50W) much faster than the Full Spectrum Laser Muse Core (45W)?

Higher wattage typically means faster cutting and the ability to cut thicker material in fewer passes. The Gweike Cloud (50W) cuts thicker material in single passes and engraves at higher speeds than the Full Spectrum Laser Muse Core (45W). For raster engraving the difference is smaller because surface engraving is limited by mechanical scan speed.

Popular Comparisons

xtool s1 vs glowforge pro xtool s1 vs xtool p2 omtech 40w co2 vs glowforge basic sculpfun s30 pro vs xtool s1 commarker b4 vs jpt mopa 30w fiber xtool f1 vs commarker b4

Settings are community-contributed and may not reflect your exact machine configuration or material batch. Always test on scrap first. Some links are affiliate links: we may earn a small commission at no extra cost to you.

What Makers Say

★★★★★5.0· 6 reviews

View all on Etsy →

★★★★★

"Used it with a Glowforge: engraved beautifully with no changes. I will be purchasing more digital downloads from this shop."

: Anna

★★★★★

"I was struggling with lining up my NFC business cards. I was able to not only line them up much better but also do multiple cards at once: making that job so much easier."

: Camp

★★★★★

"Excellent quality and design. Cut clean and neat!"

: LYNN

★★★★★

"Great jigs. Appreciate the time saved not having to build this from scratch!"

: Bruce

★★★★★

"Excellent quality. Item as described. Expectations exceeded."

: Michael

★★★★★

"This template made my slate coasters so much easier. 4×4 coasters from Michaels drop in easily and are easy to remove. Def worth it."

: chris

Leave a review →