Material · Operation	NEJE Max 4 E40	Bambu Laser
3mm Baltic Birch Plywoodcut	-	2800 mm/min · 100% · 2× passes · air assist
3mm Basswood Plywoodcut	300 mm/min · 95% · 2× passes · air assist	3000 mm/min · 100% · 2× passes · air assist
3mm Clear Acryliccut	700 mm/min · 100% · 4× passes · air assist	1200 mm/min · 90% · 2× passes
3mm MDFcut	250 mm/min · 100% · 4× passes · air assist	2500 mm/min · 85% · 2× passes · air assist
3mm Walnut Plywoodcut	-	400 mm/min · 100% · 2× passes
Bamboo 3mmcut	-	300 mm/min · 100% · 2× passes
Bamboocut	-	1400 mm/min · 95–100% · 2× passes · air assist
Basswoodcut	-	2500 mm/min · 85% · 2× passes · air assist
Cardboardcut	-	5000 mm/min · 45%
Cardstockcut	-	6000 mm/min · 22%
Chipboard 2mmcut	-	800 mm/min · 90%
Cork 3mmcut	-	2500 mm/min · 60%
Corkcut	-	4000 mm/min · 70%
Cotton Fabriccut	-	1200 mm/min · 80%
Denim Fabriccut	-	1000 mm/min · 85%
Feltcut	-	3500 mm/min · 58%
Genuine Leather (Veg-Tan, ~3mm)cut	-	2500 mm/min · 85–95% · 2× passes · air assist
Genuine Leathercut	800 mm/min · 85% · 2× passes · air assist	1400 mm/min · 80–85% · 2× passes · air assist
Kraft Papercut	-	800 mm/min · 60%
Leathercut	-	1400 mm/min · 80–85% · 2× passes · air assist
Maplecut	-	1800 mm/min · 90–100% · 4× passes · air assist
Plywoodcut	-	2500 mm/min · 85% · 2× passes · air assist
Walnutcut	-	1800 mm/min · 90–100% · 4× passes · air assist
3mm Baltic Birch Plywoodengrave	-	7500 mm/min · 35–40%
3mm Basswood Plywoodengrave	3500 mm/min · 55%	7500 mm/min · 35–40%
3mm Clear Acrylic (Cast)engrave	-	2800 mm/min
3mm Clear Acrylicengrave	2500 mm/min · 40–45%	3500 mm/min · 35–40%
3mm Maple Plywoodengrave	-	2000 mm/min
3mm MDFengrave	2000 mm/min · 40–45%	7500 mm/min · 35–40%
3mm Mirrored Acrylicengrave	-	2600 mm/min
3mm Walnut Plywoodengrave	-	2000 mm/min · 42%
Anodized Aluminumengrave	-	4000 mm/min · 65%
Bamboo 3mmengrave	-	2000 mm/min · 45%
Bamboo Cutting Boardengrave	-	3500 mm/min · 50%
Bambooengrave	-	5000 mm/min · 65%
Basswoodengrave	-	4000 mm/min · 42%
Cardboardengrave	-	8000 mm/min · 15–20%
Cardstockengrave	-	8000 mm/min · 10–15%
Ceramic Tileengrave	-	600 mm/min · 100%
Chipboard 2mmengrave	-	3000 mm/min · 42%
Coated Stainless Steel Tumblerengrave	-	4000 mm/min · 60%
Corkengrave	-	4000 mm/min · 32%
Cotton Fabricengrave	-	3500 mm/min · 28%
Denim Fabricengrave	-	2500 mm/min · 42%
Faux Leatherengrave	-	3000 mm/min · 35%
Genuine Leather (Veg-Tan, ~3mm)engrave	-	6000 mm/min · 60–70% · air assist
Genuine Leatherengrave	1500 mm/min · 45%	2800 mm/min · 38%
Glassengrave	-	7000 mm/min · 60–70%
Kraft Paperengrave	-	3000 mm/min · 28%
Leatherengrave	-	5000 mm/min · 55%
Mapleengrave	-	5000 mm/min · 65–75% · air assist
Plywoodengrave	-	7500 mm/min · 35–40%
Rubber Stamp Materialengrave	-	1200 mm/min · 70%
Slate (coaster)engrave	-	5000 mm/min · 70–80%
Slateengrave	2500 mm/min · 68%	2000 mm/min · 70%
Walnutengrave	-	5000 mm/min · 65–75% · air assist

All NEJE Max 4 E40 settings →All Bambu Laser settings →

Shopping for a NEJE Max 4 E40? Check the current price.

See price on Amazon →

Shopping for a Bambu Laser? Check the current price.

See price on Amazon →

Frequently Asked Questions

Which is better, the NEJE Max 4 E40 or Bambu Laser?

It depends on your use case. NEJE Max 4 E40 is 11W diode. Bambu Laser is 10W diode with 400×400mm bed. See the decision guide and side-by-side specs above.

What materials can both the NEJE Max 4 E40 and Bambu Laser cut or engrave?

Both machines have community-tested settings for 5 shared materials. The settings table above lists every material with side-by-side speed, power, passes, and air assist values for direct comparison.

Is the NEJE Max 4 E40 (11W) much faster than the Bambu Laser (10W)?

Higher wattage typically means faster cutting and the ability to cut thicker material in fewer passes. The NEJE Max 4 E40 (11W) cuts thicker material in single passes and engraves at higher speeds than the Bambu Laser (10W). For raster engraving the difference is smaller because surface engraving is limited by mechanical scan speed.

Popular Comparisons

xtool s1 vs glowforge pro xtool s1 vs xtool p2 omtech 40w co2 vs glowforge basic sculpfun s30 pro vs xtool s1 commarker b4 vs jpt mopa 30w fiber xtool f1 vs commarker b4

Settings are community-contributed and may not reflect your exact machine configuration or material batch. Always test on scrap first. Some links are affiliate links: we may earn a small commission at no extra cost to you.

What Makers Say

★★★★★5.0· 6 reviews

View all on Etsy →

★★★★★

"Used it with a Glowforge: engraved beautifully with no changes. I will be purchasing more digital downloads from this shop."

: Anna

★★★★★

"I was struggling with lining up my NFC business cards. I was able to not only line them up much better but also do multiple cards at once: making that job so much easier."

: Camp

★★★★★

"Excellent quality and design. Cut clean and neat!"

: LYNN

★★★★★

"Great jigs. Appreciate the time saved not having to build this from scratch!"

: Bruce

★★★★★

"Excellent quality. Item as described. Expectations exceeded."

: Michael

★★★★★

"This template made my slate coasters so much easier. 4×4 coasters from Michaels drop in easily and are easy to remove. Def worth it."

: chris

Leave a review →