Bonny Creations
Bonny Creations
Sign In
← All Machines

xTool F1 Ultra (UV) vs ComMarker B6 20W UV — Which Should You Buy?

Side-by-side specs, settings, and decision guide. Both have community-tested settings for 28 shared materials.

xTool F1 Ultra (UV): $2,499 vs ComMarker B6 20W UV: $2,499 — prices as of 2026, check retailer for current pricing.

Where to buy

Buy the xTool F1 Ultra (UV) — check current price & availability

Buy on xTool →

Affiliate link — we may earn a small commission at no extra cost to you.

Which one should you buy?

Pick the xTool F1 Ultra (UV) if you want: native LightBurn support (industry-standard).

Pick the ComMarker B6 20W UV if you want: more cutting power (20W vs 2W).

xTool F1 Ultra (UV)

Price
$2,499
Power
2W
Laser Type
uv
Software
xTool Creative SpaceLightBurn
Buy xTool F1 Ultra (UV) →

ComMarker B6 20W UV

Price
$2,499
Power
20W
Laser Type
uv
36 settings for xTool F1 Ultra (UV)35 settings for ComMarker B6 20W UV

Settings Comparison

Material · OperationxTool F1 Ultra (UV)ComMarker B6 20W UV
Cardstock 300gsmcut100 mm/s · 95%400 mm/s · 50%
Cardstockcut400 mm/s · 35%600 mm/s · 30%
Cork Sheet 3mmcut50 mm/s · 95%50 mm/s · 95%
Craft Felt 3mmcut80 mm/s · 90%80 mm/s · 90%
EVA Foam 3mmcut500 mm/s · 40%700 mm/s · 35%
Feltcut500 mm/s · 42%500 mm/s · 42%
Kraft Papercut120 mm/s · 90%120 mm/s · 90%
3mm Black Acrylicengrave500 mm/s · 30%700 mm/s · 28%
3mm Clear Acrylic (Cast)engrave350 mm/min350 mm/min
3mm Clear Acrylicengrave400 mm/s · 25%600 mm/s · 22%
3mm Mirrored Acrylicengrave300 mm/min300 mm/min
Anodized Aluminumengrave400 mm/s · 35%600 mm/s · 30%
Bamboo 3mmengrave300 mm/s · 80%300 mm/s · 78%
Bamboo Cutting Boardengrave500 mm/s · 42%700 mm/s · 38%
Bambooengrave600 mm/s · 40%800 mm/s · 35%
Basswoodengrave600 mm/s · 45%800 mm/s · 40%
Ceramic Mugengrave200 mm/s · 45%300 mm/s · 35%
Ceramic Tileengrave250 mm/s · 45%350 mm/s · 35%
Corkengrave500 mm/s · 35%700 mm/s · 32%
Faux Leatherengrave400 mm/s · 32%600 mm/s · 28%
Genuine Leatherengrave500 mm/s · 30%700 mm/s · 28%
Glassengrave300 mm/s · 35%400 mm/s · 30%
Marble Tileengrave200 mm/s · 45%300 mm/s · 40%
Slate (coaster)engrave250 mm/s · 50%400 mm/s · 42%
Slateengrave250 mm/s · 50%350 mm/s · 45%
White Acrylicengrave450 mm/s · 28%600 mm/s · 25%
Anodized Aluminummark400 mm/s · 90%800 mm/s · 80%
Black Anodized Aluminummark600 mm/s · 90%1200 mm/s · 80%
Glassmark200 mm/s · 80%—
Stainless Steelmark200 mm/s · 60%300 mm/s · 55%
All xTool F1 Ultra (UV) settings →All ComMarker B6 20W UV settings →

Ready to buy the xTool F1 Ultra (UV)?

Buy on xTool →

Frequently Asked Questions

Which is better, the xTool F1 Ultra (UV) or ComMarker B6 20W UV?

It depends on your use case. xTool F1 Ultra (UV) is 2W uv. ComMarker B6 20W UV is 20W uv. See the decision guide and side-by-side specs above.

What materials can both the xTool F1 Ultra (UV) and ComMarker B6 20W UV cut or engrave?

Both machines have community-tested settings for 28 shared materials. The settings table above lists every material with side-by-side speed, power, passes, and air assist values for direct comparison.

Is the xTool F1 Ultra (UV) or ComMarker B6 20W UV compatible with LightBurn?

The xTool F1 Ultra (UV) works natively with LightBurn. The ComMarker B6 20W UV uses . LightBurn compatibility may be possible via a community device profile but is not officially supported.

Is the ComMarker B6 20W UV (20W) much faster than the xTool F1 Ultra (UV) (2W)?

Higher wattage typically means faster cutting and the ability to cut thicker material in fewer passes. The ComMarker B6 20W UV (20W) cuts thicker material in single passes and engraves at higher speeds than the xTool F1 Ultra (UV) (2W). For raster engraving the difference is smaller because surface engraving is limited by mechanical scan speed.

Popular Comparisons

xtool s1 vs glowforge proxtool s1 vs xtool p2omtech 40w co2 vs glowforge basicsculpfun s30 pro vs xtool s1commarker b4 vs jpt mopa 30w fiberxtool f1 vs commarker b4

Settings are community-contributed and may not reflect your exact machine configuration or material batch. Always test on scrap first. Some links are affiliate links — we may earn a small commission at no extra cost to you.

What Makers Say

★★★★★5.0· 6 reviews
View all on Etsy →
★★★★★

"Used it with a Glowforge — engraved beautifully with no changes. I will be purchasing more digital downloads from this shop."

— Anna

★★★★★

"I was struggling with lining up my NFC business cards. I was able to not only line them up much better but also do multiple cards at once — making that job so much easier."

— Camp

★★★★★

"Excellent quality and design. Cut clean and neat!"

— LYNN

★★★★★

"Great jigs. Appreciate the time saved not having to build this from scratch!"

— Bruce

★★★★★

"Excellent quality. Item as described. Expectations exceeded."

— Michael

★★★★★

"This template made my slate coasters so much easier. 4×4 coasters from Michaels drop in easily and are easy to remove. Def worth it."

— chris

Leave a review →