Bonny Creations
Bonny Creations
Sign In
← All Machines

Monport EffI10S 100W CO2 vs Boss LS-2440: Which Should You Buy?

Side-by-side specs, settings, and decision guide. Both have community-tested settings for 5 shared materials.

Which one should you buy?

Pick the Boss LS-2440 if you want: native LightBurn support (industry-standard).

Where to buy

Monport EffI10S 100W CO2: check current price & availability

See current price →

Affiliate link: we may earn a small commission at no extra cost to you.

Where to buy

Boss LS-2440: check current price & availability

See price on Amazon →

Affiliate link: we may earn a small commission at no extra cost to you.

Monport EffI10S 100W CO2

Power
100W
Laser Type
co2
Buy Monport EffI10S 100W CO2 →

Boss LS-2440

Power
100W
Laser Type
co2
Work Area
610×1016mm
Software
LightBurn
Buy Boss LS-2440 →
59 settings for Monport EffI10S 100W CO29 settings for Boss LS-2440

Settings Comparison

Material · OperationMonport EffI10S 100W CO2Boss LS-2440
3mm Baltic Birch Plywoodcut42 mm/s · 40% · air assist-
3mm Basswood Plywoodcut42 mm/s · 25% · air assist50 mm/s · 25% · air assist
3mm Clear Acryliccut32 mm/s · 42% · air assist38 mm/s · 50% · air assist
3mm MDFcut46 mm/s · 44% · air assist1800 mm/min · 65% · air assist
3mm Walnut Plywoodcut47 mm/s · 28%-
6mm Baltic Birch Plywoodcut30 mm/s · 65%-
6mm MDFcut27 mm/s · 44%-
Bamboo 3mmcut50 mm/s · 58%-
Bamboo Cutting Boardcut21 mm/s · 73–78% · air assist-
Bamboocut300 mm/min · 55–60% · 2× passes · air assist-
Basswoodcut42 mm/s · 41% · air assist-
Cardboardcut64 mm/s · 26%-
Cardstockcut81 mm/s · 16%-
Chipboard 2mmcut57 mm/s · 31%-
Cork 3mmcut46 mm/s · 25%-
Corkcut47 mm/s · 36%-
Cotton Fabriccut55 mm/s · 15%-
Denim Fabriccut23 mm/s · 34%-
Faux Leathercut68 mm/s · 24%-
Genuine Leather (Veg-Tan, ~3mm)cut77 mm/s · 24–34% · air assist-
Genuine Leathercut20 mm/s · 45–50% · air assist22 mm/s · 50–55% · air assist
Kraft Papercut205 mm/s · 7%-
Leathercut19 mm/s · 36% · air assist-
Maplecut37 mm/s · 35–45%-
Plywoodcut42 mm/s · 40% · air assist-
Rubber Stamp Materialcut12 mm/s · 73–78% · air assist-
Walnutcut37 mm/s · 35–45%-
3mm Baltic Birch Plywoodengrave589 mm/s · 9–14%-
3mm Basswood Plywoodengrave439 mm/s · 20%500 mm/s · 20%
3mm Clear Acrylicengrave500 mm/s · 9–14%250 mm/s · 10–15%
3mm MDFengrave625 mm/s · 10–15%5500 mm/min · 25–30%
3mm Walnut Plywoodengrave546 mm/s · 6%-
Anodized Aluminumengrave290 mm/s · 13% · air assist-
Bamboo 3mmengrave434 mm/s · 17%-
Bamboo Cutting Boardengrave390 mm/s · 25%-
Bambooengrave589 mm/min · 36%-
Basswoodengrave589 mm/s · 9–14%-
Cardboardengrave500 mm/s · 4–9%-
Cardstockengrave500 mm/s · 4–9%-
Ceramic Tileengrave250 mm/s · 55%-
Chipboard 2mmengrave537 mm/s · 8%-
Coated Stainless Steel Tumblerengrave524 mm/min · 35%-
Corkengrave537 mm/s · 9–14%-
Cotton Fabricengrave726 mm/s · 6%-
Denim Fabricengrave394 mm/s · 9%-
Faux Leatherengrave500 mm/s · 7%-
Genuine Leather (Veg-Tan, ~3mm)engrave513 mm/s · 4–10% · air assist-
Genuine Leatherengrave342 mm/s · 16%400 mm/s · 18%
Glassengrave561 mm/s · 3–7%-
Kraft Paperengrave500 mm/s · 7%-
Leatherengrave218 mm/s · 8–13%-
Mapleengrave465 mm/s · 7–12%-
Marble Tileengrave155 mm/s · 37%-
Plywoodengrave589 mm/s · 9–14%-
Rubber Stamp Materialengrave219 mm/s · 23%-
Slate (coaster)engrave561 mm/s · 3–10%-
Slateengrave318 mm/s · 56%400 mm/s · 30% · air assist
Stainless Steelengrave361 mm/s · 45%-
Walnutengrave465 mm/s · 7–12%-
All Monport EffI10S 100W CO2 settings →All Boss LS-2440 settings →

Shopping for a Monport EffI10S 100W CO2? Check the current price.

See current price →

Shopping for a Boss LS-2440? Check the current price.

See price on Amazon →

Frequently Asked Questions

Which is better, the Monport EffI10S 100W CO2 or Boss LS-2440?

It depends on your use case. Monport EffI10S 100W CO2 is 100W co2. Boss LS-2440 is 100W co2 with 610×1016mm bed. See the decision guide and side-by-side specs above.

What materials can both the Monport EffI10S 100W CO2 and Boss LS-2440 cut or engrave?

Both machines have community-tested settings for 5 shared materials. The settings table above lists every material with side-by-side speed, power, passes, and air assist values for direct comparison.

Is the Boss LS-2440 or Monport EffI10S 100W CO2 compatible with LightBurn?

The Boss LS-2440 works natively with LightBurn. The Monport EffI10S 100W CO2 uses . LightBurn compatibility may be possible via a community device profile but is not officially supported.

Popular Comparisons

xtool s1 vs glowforge proxtool s1 vs xtool p2omtech 40w co2 vs glowforge basicsculpfun s30 pro vs xtool s1commarker b4 vs jpt mopa 30w fiberxtool f1 vs commarker b4

Settings are community-contributed and may not reflect your exact machine configuration or material batch. Always test on scrap first. Some links are affiliate links: we may earn a small commission at no extra cost to you.

What Makers Say

★★★★★5.0· 6 reviews
View all on Etsy →
★★★★★

"Used it with a Glowforge: engraved beautifully with no changes. I will be purchasing more digital downloads from this shop."

: Anna

★★★★★

"I was struggling with lining up my NFC business cards. I was able to not only line them up much better but also do multiple cards at once: making that job so much easier."

: Camp

★★★★★

"Excellent quality and design. Cut clean and neat!"

: LYNN

★★★★★

"Great jigs. Appreciate the time saved not having to build this from scratch!"

: Bruce

★★★★★

"Excellent quality. Item as described. Expectations exceeded."

: Michael

★★★★★

"This template made my slate coasters so much easier. 4×4 coasters from Michaels drop in easily and are easy to remove. Def worth it."

: chris

Leave a review →