Bonny Creations
Bonny Creations
Sign In
← All Materials

Polypropylene (Coroplast) Laser Settings

40 settings20 machines

This page lists 40 community-tested settings for Polypropylene (Coroplast). Always test on scrap before committing to your final piece. Results depend on material composition, surface finish, and coating.

📐
Phone Case Jig for Polypropylene (Coroplast) · from $3.49
Precision-aligned SVG + DXF template, sized for your machine's bed.
Browse →
Related ToolsPhone Case Jig →Rotary / Tumbler Calculator →Photo → SVG Vectorizer →Browse by Machine →
plastic

Corrugated polypropylene sign board (Coroplast/Correx) -- the common real-estate/yard-sign material. Softer and thinner than acrylic, cuts and engraves reasonably cleanly with air assist.

Buy Polypropylene (Coroplast) on Amazon →+ Submit a setting for this material

Top setting per machine

MachineOpSpeedPowerPasses
Thunder Laser Nova 24cut25 mm/s33%1
Boss LS-1420cut25 mm/s33%1
NEJE Max 4 E40cut950 mm/min65%3
xTool S1 40Wcut800 mm/min65%1
Epilog Fusion Procut20 mm/s42%1
Trotec Speedy 300cut25 mm/s39%1
FLUX Adorcut20 mm/s42%1
Snapmaker Ray 20Wcut1600 mm/min59%1
Sculpfun S10 Procut1100 mm/min62%2
K40 CO2cut10 mm/s59%1
Two Trees TS2cut1100 mm/min62%2
Longer Ray5cut550 mm/min62%3

Showing top 12 of 20 machines. See full list below.

Works with these machines

Thunder Laser Nova 24Boss LS-1420NEJE Max 4 E40xTool S1 40WEpilog Fusion ProTrotec Speedy 300FLUX AdorSnapmaker Ray 20WSculpfun S10 ProK40 CO2Two Trees TS2Longer Ray5OMTech 60W CO2Atomstack A5 ProxTool P2Monport 40W CO2Glowforge ProOrtur Laser Master 3Creality FalconxTool D1 Pro

40 settings

Thunder Laser Nova 2460Wco2
cut
Speed25 mm/sPower33%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
Thunder Laser Nova 2460Wco2
engrave
Speed300 mm/sPower6–8%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
Boss LS-142070Wco2
cut
Speed25 mm/sPower33%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
Boss LS-142070Wco2
engrave
Speed300 mm/sPower6–8%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
NEJE Max 4 E4011Wdiode
cut
Speed950 mm/minPower65%Passes3
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
NEJE Max 4 E4011Wdiode
engrave
Speed3000 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
xTool S1 40W40Wdiode
cut
Speed800 mm/minPower65%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop xTool S1 40W →More settings for this machine →
xTool S1 40W40Wdiode
engrave
Speed10800 mm/minPower17%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop xTool S1 40W →More settings for this machine →
Epilog Fusion Pro50Wco2
cut
Speed20 mm/sPower42%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
Epilog Fusion Pro50Wco2
engrave
Speed300 mm/sPower8–11%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
Trotec Speedy 30060Wco2
cut
Speed25 mm/sPower39%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
Trotec Speedy 30060Wco2
engrave
Speed300 mm/sPower8–11%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
FLUX Ador50Wco2
cut
Speed20 mm/sPower42%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop FLUX Ador →More settings for this machine →
FLUX Ador50Wco2
engrave
Speed300 mm/sPower8–11%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop FLUX Ador →More settings for this machine →
Snapmaker Ray 20W20Wdiode
cut
Speed1600 mm/minPower59%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

More settings for this machine →
Snapmaker Ray 20W20Wdiode
engrave
Speed4200 mm/minPower19–22%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

More settings for this machine →
Sculpfun S10 Pro10Wdiode
cut
Speed1100 mm/minPower62%Passes2
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Sculpfun S10 Pro →More settings for this machine →
Sculpfun S10 Pro10Wdiode
engrave
Speed3000 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Sculpfun S10 Pro →More settings for this machine →
K40 CO235Wco2
cut
Speed10 mm/sPower59%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop K40 CO2 →More settings for this machine →
K40 CO235Wco2
engrave
Speed120 mm/sPower14–17%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop K40 CO2 →More settings for this machine →
Two Trees TS210Wdiode
cut
Speed1100 mm/minPower62%Passes2
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Two Trees TS2 →More settings for this machine →
Two Trees TS210Wdiode
engrave
Speed3000 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Two Trees TS2 →More settings for this machine →
Longer Ray55Wdiode
cut
Speed550 mm/minPower62%Passes3
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Longer Ray5 →More settings for this machine →
Longer Ray55Wdiode
engrave
Speed2400 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Longer Ray5 →More settings for this machine →
OMTech 60W CO260Wco2
cut
Speed15 mm/sPower39%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop OMTech 60W CO2 →More settings for this machine →
OMTech 60W CO260Wco2
engrave
Speed180 mm/sPower10%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop OMTech 60W CO2 →More settings for this machine →
Atomstack A5 Pro10Wdiode
cut
Speed550 mm/minPower62%Passes3
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Atomstack A5 Pro →More settings for this machine →
Atomstack A5 Pro10Wdiode
engrave
Speed2400 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Atomstack A5 Pro →More settings for this machine →
xTool P255Wco2
cut
Speed80 mm/sPower29%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop xTool P2 →More settings for this machine →
xTool P255Wco2
engrave
Speed360 mm/sPower10%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop xTool P2 →More settings for this machine →
Monport 40W CO240Wco2
cut
Speed15 mm/sPower36%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Monport 40W CO2 →More settings for this machine →
Monport 40W CO240Wco2
engrave
Speed240 mm/sPower8–11%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Monport 40W CO2 →More settings for this machine →
Glowforge Pro45Wco2
cut
Speed10 mm/sPower47%Passes1
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Glowforge Pro →More settings for this machine →
Glowforge Pro45Wco2
engrave
Speed145 mm/sPower12%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Glowforge Pro →More settings for this machine →
Ortur Laser Master 310Wdiode
cut
Speed700 mm/minPower65%Passes4
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Ortur Laser Master 3 →More settings for this machine →
Ortur Laser Master 310Wdiode
engrave
Speed3000 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Ortur Laser Master 3 →More settings for this machine →
Creality Falcon10Wdiode
cut
Speed400 mm/minPower65%Passes7
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop Creality Falcon →More settings for this machine →
Creality Falcon10Wdiode
engrave
Speed2400 mm/minPower22–25%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop Creality Falcon →More settings for this machine →
xTool D1 Pro20Wdiode
cut
Speed1100 mm/minPower65%Passes2
💨 Air Assist

Air assist strongly recommended to clear melted plastic and keep the flutes from re-fusing. Typical corrugated board is ~4mm.

Shop xTool D1 Pro →More settings for this machine →
xTool D1 Pro20Wdiode
engrave
Speed3600 mm/minPower39%Passes1

Light surface engrave for house numbers/signage. Keep power low -- it melts before it chars.

Shop xTool D1 Pro →More settings for this machine →

Frequently Asked Questions

What are the best laser settings for Polypropylene (Coroplast)?

A top-rated community setting for Polypropylene (Coroplast) on the Thunder Laser Nova 24 is speed 25 mm/s, power 33%. There are 40 community-tested settings for Polypropylene (Coroplast) across 20 machines on this page.

Can a diode laser engrave or cut Polypropylene (Coroplast)?

Yes - there are 20 community settings for Polypropylene (Coroplast) on diode lasers and 20 on CO₂ lasers. CO₂ lasers generally cut faster and cleaner, but modern high-wattage diode lasers handle most plastic work well.

Do I need air assist for Polypropylene (Coroplast)?

50% of the community settings for Polypropylene (Coroplast) use air assist. Air assist is strongly recommended - it reduces charring and improves cut quality.

Some links on this page are affiliate links. We may earn a small commission at no extra cost to you.

What Makers Say

★★★★★5.0· 6 reviews
View all on Etsy →
★★★★★

"Used it with a Glowforge: engraved beautifully with no changes. I will be purchasing more digital downloads from this shop."

: Anna

★★★★★

"I was struggling with lining up my NFC business cards. I was able to not only line them up much better but also do multiple cards at once: making that job so much easier."

: Camp

★★★★★

"Excellent quality and design. Cut clean and neat!"

: LYNN

★★★★★

"Great jigs. Appreciate the time saved not having to build this from scratch!"

: Bruce

★★★★★

"Excellent quality. Item as described. Expectations exceeded."

: Michael

★★★★★

"This template made my slate coasters so much easier. 4×4 coasters from Michaels drop in easily and are easy to remove. Def worth it."

: chris

Leave a review →