Genuine Leather

Warm dark engrave on veg-tan. 45% power good starting point.

Clean dark mark on veg-tan leather.

Great results on leather. 22W handles leather well.

Rich dark engrave on veg-tan leather. Good detail at 270 LPI.

Excellent results on veg-tan. Rich dark contrast.

Clean dark engrave on veg-tan leather. Reduce power for thinner hides.

Deep dark mark on veg-tan leather.

Rich dark engrave on vegetable tanned leather.

Deep rich engrave on leather at 12W.

Rich dark mark on veg-tan leather. Slightly slower than 10W.

Clean leather cuts. Watch for fire on thick pieces.

Rich dark engrave on veg-tan leather.

UV marks leather without burning smell. Very fine detail possible.

UV engraves leather without burning smell. Clean edge detail.

0

40W S1 cuts 3mm veg-tan leather in 2 passes. Strong ventilation essential.

The 40W module requires much higher speed than lower-watt machines to avoid burning leather. Recommended community starting point: 40% power / 300mm/s / 1 pass for surface engraving on veg-tan. For chrome-tan or thinner leather, reduce power to 25–30%. For deeper engrave add a second pass rather than slowing down (prevents heat buildup). Brildor xTool leather guide recommends always running a test swatch and adjusting power in 5% increments. Do NOT use air assist for leather engraving. Source: Brildor xTool leather engraving parameters guide (brildor.com/blog/en/how-engrave-leather-xtool-parameters-tip/); xTool leather laser engraving guide (xtool.com/blogs/xtool-academy/leather-laser-engraving); 3DWithUs S1 settings.

Leather needs moderate power and moderate-to-high speed to avoid burning. Community-confirmed range: power 20–60%, speed 60–80mm/s, 1 pass. ShawnMosch M1 guide documents power ~20% at 80mm/s for light surface mark on patches; Keeping It Simple Crafts used power 60% for a deeper engrave on thick genuine leather. Start at 40% power / 70mm/s and adjust — leather type (veg-tan vs chrome-tan) significantly affects results. Veg-tan takes deeper marks; chrome-tan burns faster. Do NOT use air assist for leather engraving (spreads char into the grain). Source: ShawnMosch xTool M1 laser engraving settings (shawnmosch.com/laser-engraving-settings/); Keeping It Simple Crafts leather logo guide (keepingitsimplecrafts.com); xTool leather laser engraving guide.

Creality Falcon2 22W official wiki and Scribd 661034488: 100% power, 2000 mm/min, 1 pass for 0.65mm brown leather cut. golasergo.com review confirms leather cutting at these parameters. Thicker leather (2–3mm) may require 2 passes or reduced speed to ~1200 mm/min per LA Hobby Guy community.

Creality Falcon2 22W official wiki and Scribd parameter document (scribd.com/document/661034488): 18% power, 6000 mm/min, 1 pass for 0.65mm brown leather engrave. golasergo.com Falcon2 22W review (part 2) tested leather with these exact settings and reported clean results. crealityfalcon.com leather guide recommends no air assist for leather engrave to avoid material blowback.

Creality 10W official parameter table (Scribd 651622034) lists 20% power at 3000 mm/min for 0.65mm brown leather engrave, 1 pass. 5W community on Creality forum scales power slightly higher (~25%) to achieve comparable mark depth. crealityfalcon.com blog 'How to Laser Engrave and Cut Leather' confirms general leather engrave speed range and advises against air assist to avoid excessive blow-off on thin leather.

Same settings as X20 Pro — identical laser module. Source: lahobbyguy.com/bb/viewtopic.php?t=10243 and general 20W diode community guidance. Atomstack officially lists leather as an engravable material for the A20 Pro. Vegetable-tanned leather recommended; chrome-tanned leather releases toxic fumes.

Community starting point for 20W diode leather engraving from LA Hobby Guy (lahobbyguy.com/bb/viewtopic.php?t=10243 'Leather settings for a 20W Diode laser'). General 20W diode guidance recommends 20-40% power at 2000-4000mm/min for engraving; 3000mm/min at 30% is a widely cited midpoint. Use vegetable-tanned leather only. Strong ventilation required. Lighter marks = less power or faster speed; deeper marks = more power or slower speed. Always run a material test.

Leather engraves beautifully at 52%. Even 6W is more than sufficient for surface marking on leather — the material absorbs the diode wavelength efficiently. One of the S6 Pro's best use cases. Keep power below 70% to avoid cutting through thin pieces.

Rich dark engrave on veg-tan leather at 30%. At 33W keep power low on leather — 30% is plenty. The built-in air assist helps clear debris from the engraved area. Fast throughput for leather goods production compared to 10-20W diodes.

Rich dark engrave on vegetable-tanned leather at 45%. The 10W module handles leather engraving excellently. Keep power below 60% to avoid cutting through thin leather. Test on chrome-tanned leather separately as it gives lighter, greyer marks.

Leather engraves beautifully at 55% — one of the Ray5's best use cases. Vegetable-tanned leather gives rich contrast. Even 5W handles leather engraving well because the material absorbs the diode wavelength efficiently. Keep power below 70% to avoid cutting through thin leather.

Two passes through 2mm veg-tan leather. The built-in air assist makes a noticeable difference to cut edge quality. Leather fumes require good ventilation — open-frame machines like the S30 Pro need good room airflow or a dedicated enclosure/extractor.

Rich dark engrave at 32% on veg-tan leather. At 33W keep power low for leather — it's easy to over-burn. 32% at 6000mm/min gives deep contrast without cutting through standard 2mm leather. The large bed lets you engrave multiple leather pieces simultaneously.

3 passes for 2mm veg-tan leather. The LM3's safety sensor turns off if it detects flame — ensure your air assist is keeping the cut clear to prevent triggering the safety shutoff mid-job. Leather fumes require good ventilation even with an open-frame machine.

Rich dark mark on vegetable-tanned leather. The LM3's 20W module handles leather engraving excellently. 40% at 4000mm/min gives deep contrast without cutting through. For lighter, more decorative marks (hot stamp look) drop to 28%. Test on each leather batch.

Cuts through 2mm veg-tan leather cleanly. The Beamo's small bed limits you to smaller leather pieces — earrings, keychains, and patches rather than full bags. The enclosed design makes leather cutting more pleasant than open-frame machines.

Rich dark engrave at 18%. The Beamo handles leather very well — CO2 wavelength absorbs perfectly into leather. Beam Studio's curve-based power adjustment lets you fine-tune results without running a full test matrix. One of the best compact machines for leather goods.

At 60W even 18% is plenty for leather — the Nova 35 can engrave leather very fast. For large leather goods (bags, belts, portfolios) the 900×600mm bed is a genuine advantage. Test at 15% first; the high-powered tube can surprise you on thin leather.

Clean cuts through 2mm veg-tan leather. Epilog's consistent power output means no undercut or overcut variation across the piece. Thicker leather (3-4mm) needs 2 passes at 70%. The Zing 24's small 610×305mm bed is sufficient for most jewellery and accessory production.

The Epilog gives exceptionally sharp leather engraving — fine text down to 6pt is legible. At 20% and 350mm/s you get a deep, dark mark without cutting through on standard 2mm veg-tan. For lighter colour marking (hot-stamping look) drop to 12%.

3 passes for 2mm veg-tan leather. Leather cutting produces strong fumes — good extraction is essential. The TS2 handles thin leather well for earrings and keychains. Thicker belting leather (3mm+) is better suited to a CO2 laser.

Rich dark mark on vegetable-tanned leather. 45% at 3000mm/min avoids cutting through while still giving excellent depth. Chrome-tanned leather needs slightly more power for the same visual contrast. Always test on a leather scrap first.

Leather engraves well at 50% — the 5W diode is more than enough for surface marking. Vegetable-tanned leather gives a rich dark brown. Keep power at 50% maximum; the thin diode beam concentrates a lot of energy and can cut through thin leather.

Rich dark engrave at 22% on veg-tan leather. At 40W even 22% is plenty — resist the urge to go higher. Chrome-tanned leather produces a lighter, greyish mark. Test on a scrap of the exact leather you're using as results vary significantly between tanneries.

Cuts through 2mm veg-tan leather in one pass. Leather fumes smell strongly and are unpleasant — ensure your exhaust fan is running at full capacity. The Glowforge's sealed design helps but ventilate the room well after the job.

Rich dark brown mark at 25%. Leather is easy to overpower with a 45W tube — start at 20% and increase in 3% steps. Vegetable-tanned leather gives deeper, more consistent contrast than chrome-tanned. Remove protective coating or oils from the surface before engraving.

Fast and light — leather burns easily at 40W so keep power low. 30% at 6000mm/min gives a rich dark mark on vegetable-tanned leather without going through. For photo portraits on leather, drop to 254 DPI and use Newsprint dithering.

3 passes to cut through 2mm veg-tan leather. Cutting leather produces unpleasant fumes — ensure good extraction. The B1 handles thin leather well for earrings and keychains but struggles with thick belting leather above 3mm.

Leather engraves beautifully at 45%. Vegetable-tanned leather gives a deep brown mark. Chrome-tanned leather produces a lighter, greyish mark. Always test on a scrap as leather thickness and tanning method affect results significantly.

Rich dark brown mark at 18%. Leather is very easy to overpower with CO2 — start low and step up in 2% increments. Vegetable-tanned leather gives better contrast than chrome-tanned. Remove any protective coating first.

2–3mm veg-tan in 2 passes. Air assist on for edge quality. Test on scrap — leather thickness varies significantly.

Clean dark mark on veg-tan. 42% is a solid starting point — adjust up or down for your hide thickness. Built-in air assist helps clear smoke for cleaner detail.

Excellent dark engrave on veg-tan. 40% power gives rich result without burning. Test on scrap for your specific hide.

Very low power needed at 80W for leather. Easy to overpower — always test on scrap first.

Rich dark engrave on veg-tan. Proofgrade Leather settings. Good for personalised goods and accessories.

Excellent dark engrave on veg-tan. 40W diode works beautifully on leather. Keep power at 40% to avoid burning.

Clean dark mark on veg-tan. 42% starting point — adjust for leather thickness and tannage.

2–3mm veg-tan with 2 passes. Air assist helps edge quality. Watch for overheating on tight curves in fine shapes.

Good dark engrave on veg-tan leather. Start at 40% and dial up. Result varies with hide thickness — test on scrap.

CO2 works beautifully on leather. 22% is a starting point — K40 tube output varies significantly. Always test on scrap.

2–3mm veg-tan. Keep speed moderate — too slow scorches the oils. Air assist helps edge quality.

Clean dark mark on veg-tan leather. Power varies by hide thickness — test on scrap first. Veg-tan only; never chrome-tanned leather.

Good leather engrave. Start at 20% and increase if mark is too light.

Very low power at 80W. Easy to burn leather. Test on scrap — always.

Rich dark engrave. 22% at 60W — very easy to overpower leather, test first.

Rich dark mark. Very low power needed at 55W. Easy to overpower leather.

Very low power needed for leather at 100W. Test on scrap — easy to overpower.

3–4mm leather. Clean cut, sealed edges.

Rich dark engrave. CO2 works beautifully on leather. Test power on scrap.

Clean engrave on veg-tan leather. 45% power gives a warm brown tone without burning.

Dark engrave, sharp detail. Test power — leather varies widely by tannage.

3–4mm vegetable-tanned leather. Thicker hide may need a 3rd pass.

Light touch — dark rich engrave. Test on scrap as thickness varies. No air assist needed.

What are the best laser settings for Genuine Leather?

A top-rated community setting for Genuine Leather on the Ortur Laser Master 3 is speed 1200 mm/min, power 45%. There are 114 community-tested settings for Genuine Leather across 52 machines on this page.

Can a diode laser engrave or cut Genuine Leather?

Yes - there are 70 community settings for Genuine Leather on diode lasers and 42 on CO₂ lasers. CO₂ lasers generally cut faster and cleaner, but modern high-wattage diode lasers handle most leather work well.

Do I need air assist for Genuine Leather?

41% of the community settings for Genuine Leather use air assist. Air assist is optional for most operations but can improve edge quality on cuts.